Views: 207 Author: Site Editor Publish Time: 2019-10-29 Origin: Site
The flexibility of the motorcycle faucet directly affects the safety of driving. As we all know, a flexible faucet can automatically maintain a straight motion, and once the rotation is not flexible, it may cause an accident in an emergency. So, what causes the rotation to be inflexible? Today we are talking about the pressure bearing on the faucet, which is an important part that affects the flexibility of the faucet. How to replace it?
We must first remove the hood in the maintenance of faucet. The hood is a plastic part. It cannot be forcibly opened when it is removed. In addition to the screw, it is fixed with plastic buckle inside. We need to see the structure, combine with the principle and use skills to remove it. The hood is removed to expose the inside of the handlebar fixing screw. This is a long screw rod that penetrates into the front fork tube. The end of the screw has a beveled drawing. When the beveled drawing is tightened, the handlebar can be fixed. We need to remove this first. Motorcycles that have been used for a long time are sure to be rusty. The rusty motorcycle bolts are difficult to remove.
At this time, they must not be demolished forcibly. Once the wire is broken, it is more troublesome to handle, and it will accidentally hurt your hand. How to deal with this situation? You can use a rust remover, or a silk loosening agent, or a drop of some oil. After infiltrating into it, it will be easier to disassemble. When removing the hood, be careful not to squat down directly, because there are many wires inside the hood. And there are connectors, so be sure to straighten out and disconnect the corresponding wires to ensure that the line does not affect the work.
The next step is to disassemble the fork screws. The middle screw of the handlebar is preferably removed by a sleeve or a wrench, generally with a 12cm wrench. After dropping the loosening agent or oil, if you still can't remove it, you can tap it with a hammer to loosen the screw, then use a wrench to screw down the screw. The use of the tool is also skillful. It should be leveled. Do not disassemble it forcibly. Otherwise, the outer edge of the screw will be worn away. The wrench will become smoother and it will be more difficult to disassemble.
Motorcycle faucet front fork looks simple, in fact, the things inside are complicated. The bottom is the lower block with a small curved surface, the top is the bead frame, which is above the bead bowl; The bead bowl is followed by the bead frame, the cover wire, the cover slip wire, and the set screws. These sounds complicated, but in fact, it's easy to figure out the relationship between them. This place influences the faucet rotation most. This place will wear more or less. For example, the bead frame is scattered; the steel bowl is not smooth; the lower block is deformed; the cover screw is slippery; and there are even some unexpected problems.
Purchase new parts according to the same model and be careful when installing to prevent deformation of the parts. When installing the upper and lower bead frame and the bead bowl, you should tap the position in parallel. If it is not easy to enter, you can wipe some butter. You can also use the small square wood to stand in parallel and hit it with a hammer. The upper and lower bead frames and bead bowls have high requirements for flatness, and if they are deformed, they will cause premature wear of the balls. When installing the ball, be sure to fix it with butter, which is easy to install, more lubricious, less frictional, and more flexible. In addition, the cover should not be over-tightened, otherwise it will affect the normal rolling of the ball, which will cause the ball to wear and cause the faucet to be inflexible.
After the bearing is replaced, the flexibility of the faucet must be adjusted to the desired level. After that, make sure the front fork is in the center. If the faucet is twisted, it will cause the ride to be very uncomfortable. After the mechanical part is adjusted, the plugs should be re-inserted, the line is tested to be connected and test whether the parts can work normally, especially the headlights, turn signals, and speakers. Loose connectors are best secured with a cable tie to prevent looseness and cause inexplicable failure.
Founded in 2008, JIAXING JUJIE HARDWARE TOOL CO.,LTD is located in Jiaxing, Zhejiang. It is a factory engaged in producing motorcycle bolts, motorcycle stand/lift and wheel chock, motorcycle tie down, motorcycle tool, and plastic can. If you are interested in our motorcycle tools, please contact us at any time.
